× CAMWorks 2021 SP1 for Solid Edge Close
CAMWorks 2021 SP1 for Solid Edge | 1.3 Gb
Languages: 中文 Simplified, 中文 Traditional, Français, Deutsch, Italiano, 日本語,
Polski, Português-Brazilian, Русский, Español, Türkçe, 한국어, Čeština
GeometricPLM is pleased to announce the availability of CAMWorks 2021 SP1 for Solid Edge is the premier fully integrated CAM system with all the modern features and functiona lity needed to boost machining efficiencies and maximizing shop productivity.
CAMWorks 2021 SP1 Resolved CPR’s 1. CW-106677 CSR-15873 TechDB For the specific customized based TechDB, when Mill-Turn machine is selected in CAMWorks For Solid Edge application then Solid Edge crashes.
2. CW-106643 CSR-15497 License In License Manager, the information entered by the user on the license request page is not retained upon closing and reopening the page.
3. CW-106635 CSR-15808 TechDB The thread parameters of ID and Designation are incorrectly populated for the Thread Mill operation as compared to the parameters set in the TechDB for a Multi Stepped Hole feature.
4. CW-106353 CSR-15754 Post The posted output generated for Multiaxis operation on a patterned feature using the APT post processor is incorrect.
5. CW-106220 CSR-15635 Post While posting the codes for synchronized operations, the wait code is posted before the start of the operation even though the settings are made to post the wait code before the first feed move. This happens when there is no tool change between the preceding and the current operation.
6. CW-106162 CSR-15672 Setup Sheets In CAMWorks For Solid Edge 2021 SP0 version, when the setup sheets are generated with style sheet of “Operations and WIP” then, WIP images are not generated in the setup sheets.
7. CW-106111 CSR-15620 Operation With the customized TechDB, when Save Operation Plan is done on any feature having operations then, the values defined for machining depth are replaced with large values.
8. CW-105964 CSR-15501 Rebuild In an assembly file having multiple Solid Edge configurations along with corresponding CAMWorks For Solid Edge configurations, unwanted prompt to rebuild the CAM data is shown whenever the user toggles between the configurations. This happens even when there hasn’t been any change in the CAM data.
9. CW-105937 CSR-15566 Post For the specific part, incorrect values for rotary angles are seen in the posted code of a drill toolpath generated on a patterned counter bore hole feature.
10. CW-105845 CSR-15541 TechDB In TechDB, when a new feature condition is created by copying an existing feature condition along with its operations then, the tools set in the original operations are not copied to the newly created operations.
11. CW-105844 CSR-15510 TechDB When the customized Access based TechDB is imported into SQLite based TechDB then the description for the ‘ID’ in default feature strategies is not updated correctly.
12. CW-105793 CSR-15534 TechDB In system settings if comma is used as a number separator then, the values set in Feed Speed library are reset to zero.
13. CW-105551 CSR-15494 Feature While creating feature groups of hole features the “Hole thread callout” set for the tapped holes is not considered. This results in incorrect grouping of hole features having different hole thread call outs.
14. CW-105476 CSR-15440 Operation With the customized TechDB, when the parameters of the chuck/fixtures are modified in CAMWorks For Solid Edge then, a crash of CAMWorks For Solid Edge is seen.
15. CW-105412 CSR-15339 TechDB In TechDB, while importing Harvey and Helical tools then, upon switching between the manufacturers the list of the tools is not refreshed.
16. CW-105389 CSR-15372 Operation For an Assembly file, when save operation plan is performed on Multi surface feature with Multi Axis operation then Solid Edge and CAMWorks For Solid Edge crashes.
17. CW-105383 CSR-15175 Post The output of the post variable “OPR_AXIS_Type” is automatically changed, when the option “Output Subroutine” for patterned feature is selected in posting tab of operation parameters dialog box.
18. CW-105380 CSR-15329 Post In Mill-Turn mode, the spindle speed output in the G code for Gun drill operations is incorrect.
19. CW-105353 CSR-15072 Toolpath The toolpath for rough mill operations with pattern type set to Volumill does not adhere to the geometry of the Avoid area defined by the user.
20. CW-105317 CSR-15262 Machine Simulation The UI in CAMWorks Virtual Machine is displayed in different language as compared to the language set in CAMWorks For Solid Edge.
21. CW-105305 CSR-15285 Feature For the specific Mill-Turn assembly, renaming a Solid Edge axis entity and rebuilding the CAMWorks data results in a crash of CAMWorks For Solid Edge.
22. CW-105186 CW-105185 CSR-15220 Feeds & Speed For the 64-bit Feed Speed library, the user is unable to edit or delete a row of data for 2 or 3 Axis Rough and Finish operation parameters.
23. CW-105181 CW-105076 CW-104605 CSR-15220 CSR-15200 CSR-15244 CSR-15022 CSR-15200 Feeds & Speed When the data from 32-bit F/S library is imported into the new 64 bit F/S library then, the data is found to be either incorrect or missing.
24. CW-105177 CSR-15241 Post Add the ability to list tools in the tool crib having same station number with different tool using GETTOOLS() method.
25. CW-105095 CSR-15242 Feeds & Speed In Feed Speed library, when the unit is set to ‘Inch’ and Feed Speed data for material and operation is modified then, the data is converted to metric after saving.
26. CW-105090 CSR-14858 TechDB For the customized based TechDB, when the user saves an operation plan for a specific feature then, incorrect data is saved to TechDB resulting in unwanted operations being populated for subsequent sessions.
27. CW-105056 CSR-15198 CSR-15428 CSR-15563 Feeds & Speed In Feed Speed library, an error message is observed whenever the user tries to install a material from the archive.
28. CW-105055 CSR-15201 TechDB When the customized TechDB of CAMWorks For Solid Edge 2020 is imported into CAMWorks For Solid Edge 2021 then, the values for all the parameters of probe operations are deleted.
29. CW-104741 CSR-15120 Feature For the specific assembly, when the Extract Machinable Features method is set to MfgView then, the features are incorrectly recognized.
30. CW-104739 CSR-14388 Feature In assembly mode, when Extract Machinable Features is done then, the feature setups and Part perimeter features are not created in case no other feature is recognized from that direction.
31. CW-104694 Beta 53382 UIF In Spanish language version of CAMWorks For Solid Edge, the labels of some of the parameters in Volumill settings dialog box are incorrectly translated.
32. CW-104650 CSR-15068 Setup Sheets Add a variable for ‘Surface speed RPM max’ in Turn and Mill-Turn to be used in XML setup sheet.
33. CW-104647 CSR-15058 TechDB The user is unable to set the diameter for Thread Mill operation using the components of a Multi Stepped Hole feature.
34. CW-104642 CSR-15057 Machine Simulation In CAMWorks Virtual Machine, the gang tool with live tools are not displayed.
35. CW-104540 CSR-14988 CSR-15096 System When CAMWorks For Solid Edge application is upgraded with the latest version then, all the user created custom files viz. setup sheets, sub spindle operations are deleted from the existing installation.
36. CW-104494 CSR-14993 TechDB In TechDB, the unit of measure for spindle speed is displayed as inch or metric instead of RPM for Z level operations.
37. CW-104490 CSR-14942 Machine Simulation In CAMWorks Virtual Machine with machine type set to Mill turn, duplicate entries of tool blocks with same tools are created.
38. CW-104484 CSR-14946 Post Add a new query command to pass “Arc Feedrate” and “Sharp corner feedrates” to post.
39. CW-104386 CSR-14916 UIF In Russian language version of CAMWorks For Solid Edge, the behavior of parameters of CNC compensation and Toolpath center is incorrect compared to the English language version.
40. CW-104344 CSR-104903 Machine Simulation For the specific part, a crash of Solid Edge is seen when the user selects the option of machine simulation.
41. CW-104248 CSR-14847 UIF The last saved option for stock display is not retained for sub sequent parts in CAMWorks For Solid Edge 2021. The option is always reset to wireframe mode.
42. CW-104103 CW-104066 CSR-14627 Feature For the specific Turn part, upon doing a rebuild, some of the features are incorrectly generated and an error message is displayed.
43. CW-103884 CW-102733 CSR-14679 CSR-14173 CSR-14525 Toolpath The parameters of “Arc feedrate override” do not make any impact on the side passes created using the side parameter settings for the Contour Mill toolpath.
44. CW-103816 CSR-13605 Simulation For the specific part, simulating the Multi Axis Mill operation results in a crash of CAMWorks For Solid Edge.
45. CW-103779 CSR-10552 CSR-10889 CSR-14418 Feature Switching between Solid Edge configurations results in unnecessary rebuild of CAMWorks For Solid Edge data.
46. CW-103778 CSR-12666 System A crash in CAMWorks For Solid Edge is seen when the user works with the specified parts or assemblies.
47. CW-103686 CSR-14457 Feature For the specific assembly, Multi Stepped Holes are recognized in incorrect setups thus resulting in erroneous toolpaths.
48. CW-103247 CSR-14310 Toolpath For a Contour Mill operation, when the clearance plane is defined by “Previous Machining Depth” then incorrect rapid move is observed, and the toolpath gauges the part.
49. CW-102625 CSR-13449 UIF In case of monitors having 4K resolution, some of the dialogs in CAMWorks For Solid Edge are incorrectly displayed.
50. CW-102272 CSR-13937 Toolpath The posted code for a Center Drill operation with canned cycle set to True on the sub spindle of a turn machine is incorrect.
51. CW-101836 CSR-13767 Post The post variables “OPR_X_PART_CLEARANCE” and “OPR_Z_PART_CLEARANCE” will output only clearance value not the allowance value for Turn Finish operations.
52. CW-101668 CSR-13690 UIF For the specific Mill part, the option of ‘Fixture Coordinate System’ to define the X axis of the Mill Part Setup is not available.
53. CW-101632 CSR-13667 Features For the specific part, incorrect islands are detected for some of the features extracted using ‘Extract Machinable Features’ command.
54. CW-101602 CSR-13668 Toolpath For the specific part, the toolpath for the Rough Mill operation with entry type set to Spiral gouges the feature.
55. CW-101242 CSR-13489 Toolpath For the specific part, the toolpath for Rough Mill operation with pattern type set to Volumill gouges the feature when the smoothing radius is set to 8% of the tool diameter.
56. CW-101219 CW-97098 CSR-13531 CSR-11766 Simulation For the specific part, in toolpath simulation the display of the Fixture Coordinate System defined using a Solid Edge coordinate system is incorrect.
57. CW-100977 CW-99576 CSR-13316 CSR-13035 Toolpath The geometry of the fixtures selected to be avoided in a Mill Part Setup of an assembly file is incorrectly considered for the toolpath of Rough Mill operation with pattern type set to Volumill.
58. CW-100897 CSR-13391 CSR-14297 System If the Multi axis mill machines with all parameters defined is reselected then, an error message asking the user to select the reference axis and face is displayed. This message should not be displayed as the user has already defined the parameters.
59. CW-99041 CSR-12847 Feature For the specific Mill part, incorrect wrapped engrave feature is created.
60. CW-99024 CSR-12806 UIF The display of the tooltip for the operation parameters is not completely visible in graphics area.
61. CW-98791 CSR-12718 Post For the specific part, incorrect G- Code is posted for the Multi axis Mill operation.
62. CW-98645 CSR-12569 CSR-14401 Toolpath Incorrect co-ordinates are posted for a Tapping operation generated for a feature on the lathe sub-spindle.
63. CW-96694 CSR-11566 Feature For the specific part, incorrect profile is generated for Wrapped engrave feature using the user defined sketch.
64. CW-95153 CW-93641 CSR-11058 CSR-10733 Simulation For the specific part, the display of the CAMWorks For Solid Edge origin is incorrect during simulation.
65. CW-90563 CW-87035 CSR-10226 CSR-8857 Rebuild When the origin of the coordinate system is defined as the vertex on the stock and stock size is changed then, the coordinate system is not changed unless rebuild is performed.
66. CW-87628 CSR-9312 Simulation For the specific part, an error message is displayed with toolpath simulation is done on the Rough Mill operation.
67. CW-86694 CSR-8715 Operation For the specific part, setting the cut amount to Zero for Contour Mill operation results in a crash of CAMWorks For Solid Edge.
68. CW-85667 CSR-7740 Rebuild When the Solid Edge configuration is switched to CAMWorks For Solid Edge configuration then CAMWorks For Solid Edge prompts to rebuild. However, when CAMWorks For Solid Edge configuration is changed then no Rebuild is prompted.
69. CW-82649 ––- TechDB In TechDB for single point operations in Turn or Mill Turn module allow the user to set the spindle speed only using RPM method and not SMM method.
70. CWR-1887 Beta 52657 Toolpath When the 3-axis toolpath generation method is set to Advanced then, for the specific part, a gouge is seen with the toolpath of Constant Stepover operation.
71. CWR-1885 CSR-14816 Toolpath When 3 axis toolpath generation method is set to Advanced then, for the specific part the toolpath of Flat Area operation is not generated.
72. CWR-1877 CSR-14642 Toolpath When the 3 Axis toolpath generation method is set to Advanced then, the toolpath for Area Clearance operation using a User Defined tool is not generated with pattern type set to adaptive.
73. CWR-1869 CSR-14472 Toolpath When the 3 Axis toolpath generation method is set to Advanced, then the toolpath generated for Flat Area operation is not within tolerance.
74. CWR-1837 CSR-13714 Toolpath When the 3 Axis toolpath generation method is set to Advanced, then for the specific part some of the moves of the toolpath of Area Clearance operation do not adhere to the cut direction of “Climb” as defined by the user.
75. CWR-1835 CSR-13728 Toolpath When the 3 Axis toolpath generation method is set to Advanced, then for the specific part the toolpath for Flat Area operation is not generated.
76. CWR-1797 CSR-12730 Toolpath When the 3 Axis toolpath generation method is set to Advanced then, for the specific part no toolpath is generated for Area Clearance operation when holder avoidance is set to True.
77. CWR-1786 CSR-12376 Toolpath When 3 axis toolpath generation method is set to Advanced then, for the specific part the toolpath generated for Constant Stepover operation with horizontal lead-in or lead-out gouges the part.
78. CWR-1727 CSR-11547 Toolpath When 3 axis toolpath generation method is set to Advanced then, for the specific part the toolpath generated for Z level operation does not adhere to the user defined Z limits.
79. CWR-1659 CSR-10467 Toolpath When 3 axis toolpath generation method is set to Advanced then, incorrect toolpath is generated for the area clearance operation with depth method set to Scallop along with adaptive step down set to On and with the user defined Z limits.
× CAMWorks 2021 SP1 for Solid Edge Close
CAMWorks was first published as an add-in application for numerically controlled (NC) tool programming in SolidWorks in 1997. In June 2013, Geometric Software released a version of CAMWorks integrated with Solid Edge, the value priced CAD system from Siemens PLM Software. Although seven computer-aided manufacturing (CAM) software products have achieved so-called Gold Partner integration with SolidWorks, CAMWorks is the first such software to be seamlessly embedded within Solid Edge.
CAMWorks for Solid Edge allows programmers to open a part file in native format and begin making a numerically controlled tool program immediately. There is no need to export software to another format and import it into an NC programming tool. When complete, tool paths and other CAM information are stored in the Solid Edge model.
Changes made to Solid Edge parts are immediately reflected in NC programs produced by CAMWorks. CAM systems that are not integrated with CAD require revised parts to be re-exported, and in most cases updates to geometry must be made interactively.
CAMWorks for 2021 provides advanced new features to help you take full advantage of your CNC machines
What's New in CAMWorks 2021
GeometricPLM by HCL Technologies a specialist in the domain of engineering solutions, services and technologies. Its portfolio of Global Engineering services, Product Lifecycle Management (PLM) solutions, Embedded System solutions, and Digital Technology solutions enables companies to formulate, implement, and execute global engineering and manufacturing strategies aimed at achieving greater efficiencies in the product realization lifecycle.
On April 1st 2016, Geometric got into an agreement with HCL Technologies to transfer of its business to HCL Tech by way of demerger, except for its 58% share in the joint venture with Dassault Systèmes (3DS) (3DPLM Software Solutions Limited (3DPLM)). The transition has become effective on March 2nd 2017, after seeking all statutory approvals.
Product: CAMWorks
Version: 2021 SP1 (build 2021/0415)
Supported Architectures: x64
Website Home Page : www.camworks.com
Language: multilanguage
System Requirements: PC *
Size: 1.3 Gb
* System Requirements: Before installing CAMWorks 2021, ensure that the following system requirements are fulfilled:
Supported Microsoft Windows Operating Systems
The 64-bit version of:
- 64-bit version of Windows 10
- 64-bit version of Windows 8.1
- 64-bit version of Windows 7 (SP1 or higher)
** Home editions of the above Operating Systems are not supported.
Supported CAD applications
CAMWorks For Solid Edge runs as an Add-in within Solid Edge. The following versions of CAD applications support CAMWorksForSolidEdge2020x64:
- 64-bit version of Solid Edge 2021 MP00 or higher
- 64-bit version of Solid Edge 2020 MP07 or higher
Hardware Requirements
RAM: 8 GB or more recommended
Video Card: Certified cards and drivers
Processor: Intel or AMD processors with SSE2 support. 64-bit operating system required.
USB port: User may choose to have CAMWorks license on a USB dongle (key). CAMWorks Hardware dongle (key)plugs into the USB port.
Network: Microsoft's Windows Networking and Active Directory network environments.
Install Media: Broadband Internet Connection
Please visit my blog
Added by 3% of the overall size of the archive of information for the restoration
No mirrors please
× CAMWorks 2021 SP1 for Solid Edge Close
Download File Size:1.3 GB
|
