NetSim for CCNP 8.0 is designed to help you learn the Cisco IOS command structure, and it supports the technologies and skills required for the recently revised CCNP certification.
NetSim for CCNP includes new labs for the ROUTE, SWITCH and TSHOOT technologies. In addition to new content, NetSim for CCNP 8.0 contains a new and improved interface that makes completing labs, compiling new labs and designing network topologies easier than ever before. The network topology, device consoles and lab instructions can share the screen in NetSim 8.0 with easy-to-use panes. NetSim 8.0 also supports multiple monitors.
Everything you need to create and compile new labs – from the NetMap topology designer, to the device configuration window, to the saving and merging of files – are all in one easily navigable window. Completing NetSim labs and creating your own labs have never been so easy.
Additional Resources
NetSim 8.0 User Manual. (Best viewed when using Acrobat viewer.)
How to compile a lab using NetSim 8.0. (PDF)
NetSim for CCNP 8.0 Enhancements
Vastly improved user interface
External lab document viewer enables the use of multiple monitors
Telnet mode enables the user to open a separate Telnet session for each device in the simulated topology
New labs supporting ROUTE, SWITCH and TSHOOT technologies
Supports EIGRP debugging
Improved EIGRP – less processor intensive
Support for HSRP, MHSRP and VRRP
Boson NetSim for CCNP 8.0 Network Simulator Offers
Hands-on experience without the hardware
A Network Designer that supports 42 routers and 6 switches
Up to 200 devices per network
Virtual Packet Technology: software-created packets that are routed and switched through the simulated network
The ability to populate the WAN slots with a broad range of Network Modules
A Telnet mode that allows you to configure devices in the simulated topology using the Windows telnet program
The functionality of a full rack of equipment on your laptop
Automatic lab-grading capability
The ability to load and save your network configurations
The ability to paste real router configurations into the devices
The ability to configure your own ISDN and Frame Relay switch mappings
The benefit of connecting your devices over simulated WANs without expensive ISP gear
Support for IPv6 addressing
NetSim for CCNP 8.0 Devices
42 Routers (Cisco devices)
6 Switches (Cisco devices)
5 PCs: TFTP, Traffic generator, AAA Server, VPN Client, workstation
1 IP Phone
48 total Cisco devices
54 total devices
New CCNP Labs Include
Configuring EIGRP III
EIGRP and Frame Relay
Influence EIGRP Path Selection
Optimizing EIGRP
EIGRP Authentication
Configuring Hot Standby Router Protocol
Configuring Virtual Router Redundancy Protocol
Configuring Multiple Hot Standby Router Protocol
Troubleshooting EIGRP Routing
Troubleshooting Hot Standby Router Protocol
Configuring Hot Standby Router Protocol (HSRP)
Configuring Virtual Router Redundancy Protocol (VRRP)
Configuring Multiple Hot Standby Router Protocol (MHSRP)
Labs for CCNP
2950 Deleting VLANs
2950 IP Addresses
2950 Spanning Tree
2950 Telnet
2950 Trunk
2950 VLANs
2950 VTP
2950 VTP with Client
AAA
AAA Login Authentication and Exec Authorization
Access List Review
Address Optimization
Advanced Access Lists
Advanced Router Config
Applying Security Tools
ARP
Backing up a WAN Connection with IPSEC VPN
Backup Interface
Backup Using TFTP
Basic Router Config
Basic Show Commands
BGP
Catalyst 1900 Switch Config
Catalyst 2950 Switch Config
CDP
CHAP and RIP
Cisco Discovery Protocol – Router
Configuring a Switch for a WLAN
Configuring Class-Based Header Compression
Configuring EIGRP I
Configuring EIGRP II
Configuring EIGRP III
Configuring FIFO and WFQ Queuing Mechanisms
Configuring Frame Mode MPLS
Configuring GRE Tunnels over IPsec using SDM
Configuring Hot Standby Router Protocol
Configuring IOS Security Part 1 – VLAN ACL’s
Configuring IOS Security Part 2 – TACACS+
Configuring IPv6
Configuring IPv6 Routing
Configuring IPv6 Tunnels
Configuring LFI
Configuring Multiple Hot Standby Router Protocol
Configuring NBAR
Configuring OSPF
Configuring QoS
Configuring QoS Preclassify
Configuring QoS with Cisco AutoQoS
Configuring Router Interfaces
Configuring Static and OSPFv3 Routing
Configuring Support for IP Telephony
Configuring Switch Interfaces
Configuring the LLQ Queuing Mechanism
Configuring Virtual Router Redundancy Protocol
Connectivity Test with TraceRoute
Creating a Host Table
Default Routes
Demo Lab
EIGRP and Frame Relay
EIGRP and Wildcard Masks
EIGRP Authentication I
EIGRP Authentication II
EIGRP Routes
Extended Access Lists
Extended Access Lists with RIP
Frame Relay
Frame Relay Full Mesh
Frame Relay Hub-and-Spoke
Frame Relay with Dial Backup
Hierarchical IP Addressing
IGRP
IGRP Routes
Implementing Multiple Spanning Tree Protocol
Implementing NAT
Implementing NAT II
Influence EIGRP Path Selection
Inter VLAN Routing
Initial Config
Introduction to MQC and the SDM QoS Wizard
IOS Switching Initial Configuration
IP Access Lists
IP Addressing
IPSEC
ISDN
ISDN BRI
ISDN BRI-BRI Using Dialer Profiles
ISDN BRI-BRI Using Legacy DDR
ISDN Dialer Profiles
ISDN PRI Using Dialer Profiles
IS-IS
Lab Primer
Layer 3 Switching
Layer 3 Switching and Layer 2 Security
Loopback Interfaces
Low Latency Queuing
Many-to-One NAT
Multi-Area OSPF
Multi-Area OSPF and Routing Table Optimization
Multicast Routing
Multi-Site Frame Relay and Policy Routing
Multi-Site Network
Named Access Lists
NAT
This Product Covers: Certification
640-802 CCNA
640-822 ICND1 (Interconnecting Cisco Networking Devices Part 1)-CCENT
640-816 ICND2 (Interconnecting Cisco Networking Devices Part 2)-CCNA
642-813 SWITCH-CCNP
642-832 TSHOOT-CCNP
642-902 ROUTE-CCNP
Download File Size:81.95 MB
|
